Bradstone Natural Limestone Paving Honeymede stands out for all the right reasons. It shares the same detailing and natural veining as our other limestone paving solutions but is distinguished by its warmer hues and lighter shades.
Available in a patio pack of six compatible sizes enabling them to be laid easily.
Each pack contains the following mix of sizes:
- 6 slabs of 600mm x 600mm
- 10 slabs of 600mm x 450mm
- 10 slabs of 600mm x 300mm
- 10 slabs of 450mm x 450mm
- 5 slabs of 450mm x 300mm
- 4 slabs of 300mm x 300mm
(Total 45 units)
NEVER use an acid based cleaner on any natural limestone product either as a wash or to remove mortar stains. The chemical reaction resulting from acid being applied to a limestone product will permanently damage the surface of the stone.
To maintain the "as new" appearance of limestone paving, it is recommended that you seal the product to prevent colour fade.
For more information on the cleaning and sealing of this product, please contact the Simply Paving office on 0800 032 6306.
When laid using a 10-15mm joint each pack contains enough paving slabs to cover 10.20m2.
Thickness: 22mm - Country of origin: India
Deliveries normally occur between 7am and 6pm. Once your order has been placed you will be contacted and provided with an exact date of delivery.
This vehicle will lower the product to the ground using an electric lift. The pallet of products is then pulled off using a manual pallet truck. It is imperative that the ground that the pallet is unloaded onto is flat and solid. Access may be needed for a rigid lorry (up to 20ft) otherwise additional delivery charges may be made. For larger orders alternative delivery methods can be arranged. Please call our office to discuss any delivery requirements or for clarification.
Our customer services team will advise how to prepare for receipt of ordered goods. Our delivery team are not responsible for any additional lifting or carrying of your goods.
We do not deliver items to multiple addresses.
All full packs and all orders containing at least one full pack will be delivered free of charge*. All orders of £300 or more (even if only containing individual units) will be delivered free of charge*. Orders for individual units with an order value of less than £300 usually have a flat delivery charge of £30.
*Delivery is free on orders with full packs except for deliveries to the postcodes AB, BT, DD, GY, HS, IM, IV, JE, KA27-28, KW, PA20+, PH, P030-41, TR21-25 and ZE. Please refer to our Delivery Policy
for a table of charges or if you would like further information please call 0800 032 6306.
Delivery will normally be less than 7 days (typically 3-5 working days). Simply Paving will aim to contact you by email or directly by phone within two working days of your order to suggest a delivery date. If the date provided is unsuitable please get in touch and we will re-arrange the delivery date.
For further information please refer to our Delivery Policy
Download 10.20m2 Patio Pack Laying Pattern
The area to be paved should first of all be dug out to a depth of at least 200mm. The area should then be back filled with 150mm of MoT/crusher run, compacted to 100mm.
Once the area is prepared, the laying of each flag can commence. The actual mortar bed is prepared individually for each and every flag dependent on its thickness. The bed will consist of a semi-dry mortar mix, using 4 parts sharp sand to 1 part cement. Spot bedding should never be used for natural stone paving, as the flag will not be sufficiently supported.
When laying flags that will have mortar joints, the receiving edges of the already laid flags are buttered with mortar into which the new flag is pressed, forming a well filled joint, that can be topped up when pointing. Buttering will also aid consistency of joint width. Once in place, each flag can be consolidated by tapping them down, either with a rubber mallet or by keeping a piece of softwood between a hammer or mallet and the flag. Continually check levels and falls during the laying process across the top surface profile of a number of flags at a time.
Point with a wet mortar mix of 4:1 (building sand will be more workable), ensuring the gaps between the flags are completely filled. The strength of the pointing is extremely important, as if done incorrectly, the joints will be the weakest part of the paved area. It is important to take care not to stain the paving surface with any excess mortar as this will be difficult to remove.
A plasticiser can be added to the mortar mix to improve its workability and also ensure all air pockets are eliminated. Cement dyes may also be added to the mix to change the final colouration of your pointing mortar. Simply Paving can offer a jointing compound suitable for use with natural stone flags, please contact us directly for more information.
Please refer to the guides section of the website for further information regarding laying flag paving.